Kia Cee'd: Audio / Speakers Repair procedures

Kia Cee'd JD Service Manual / Body Electrical System / Audio / Speakers Repair procedures

Inspection

Troubleshooting for Speaker

(1)	Basic inspection of speaker Inspect the sound from speaker after verifying that the speaker mounting screws are removed and the wiring connector is connected to remove any possible vibration transmitted from body trims and surrounding parts.

(2)

Case Troubleshooting

No.

Case

Inspection/Remedy

Trembling sound

1)	Before replacing the speaker, inspect that the mounting screw is installed normally.

2)	After re-installing the speaker, verify that no trembling sound is heard.

3)	When hearing a trembling sound again, replace the speaker with new one.

Noise

1)	Check if the wiring connector is connected normally. If not, reconnect the wiring connector.

2)	In case of radio static, check if there is a noise from CD.

3)	If a noise is heard with the radio and CD on, replace the speaker with new one.

In case there is only radio static, this may be the cause of the poor radio reception. Thus the speaker needs no repair and replacement.

Speaker
in operative

Inspection of the wiring connection between the battery and the speaker

1)	Before replacing the speaker, inspect the wiring connection between the battery and the speaker is normal.

2)	Check the supply power to the speaker and the resistance, then inspect the sound quality. ■ Specified impedance : 4.0 ± 0.6Ω

3)	If the speaker works poorly, replace it with new one.

When handling the speakers:

–	Do not damage the speaker with impact, like dropping or throwing it.

–	Be careful not to drop water and oil on the speakers.

–	Caution during handling of speaker because the material of diaphragm is paper which is easily torn by impact or external force.

–	Modifying the audio system may cause damage to the speakers. If this is the case, the speakers are not covered by the manufacturer's warranty.

Removal

Front Speaker

1.	Remove the front door trim. (Refer to Body - "Front Door Trim")

2.	Remove the front speaker (A) after loosening 4 rivets.

Rear Speaker

[5Door]

1.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

2.	Remove the rear speaker (A) after removing 4 rivets.

[3Door]

1.	Remove the center pillar trim. (Refer to Body - "Center Pillar Trim")

2.	Remove the rear speaker assembly (A) after loosening the mounting bolts.

3.	Disconnect the connector (A) from the speaker.

Remove the rear speaker (A) after loosening the mounting screwss.

Separate the speaker connector (A) from the speaker bracket.

Tweeter Speaker

1.	Remove the crash pad side speaker grill (A).

2.	Remove the tweeter speaker (A) after loosening 2 screws.

Installation

Front Speaker

1.	Install the front speaker.

2.	Install the front door trim.

Rear Speaker

1.	Install the rear speaker.

2.	Install the rear door trim.

Tweeter Speaker

1.	Connect the connector.

2.	Install the tweeter speaker and speaker grill.

Audio Unit Repair procedures

Removal • Take care not to scratch the center fascia panel and related parts. ...

Antenna Components and components location

Components ...

Other information:

Kia Cee'd JD Service Manual: Purge Control Solenoid Valve (PCSV) Description and operation
Description Purge Control Solenoid Valve (PCSV) is installed on the surge tank and controls the passage between the canister and the intake manifold. It is a solenoid valve and is open when the ECM grounds the valve control line. When the passage is open (PCSV ON), fuel vapo ...

Kia Cee'd JD Service Manual: Auto Defogging Sensor Repair procedures
Inspection To inspect and diagnose the sensor, refer to Self-Diagnosis procedure and DTC guide. Replacement 1. Disconnect the negative (-) battery terminal. 2. Remove the auto defogging sensor cover (A) by pulling i ...