Kia Cee'd: Rear Seat / Rear Seat Cushion Cover Repair procedures
[5Door, Waggon]
[LH]
| • |
Put on gloves to protect your hands.
|
|
| • |
Use a plastic panel removal tool to remove interior trim pieces
to protect from marring the surface.
|
| • |
Take care not to bend or scratch the trim and panels.
|
|
| 1. |
Remove the rear seat cushion assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
| 2. |
Disconnect the rear seat cushion cover protector (A).
|
| 3. |
Remove the rear seat cushion frame (A).
|
| 4. |
After removing the hog-ring clips (A) on the rear of seat cushion and
remove the rear seat cushion cover (B).
|
| 5. |
Install in the reverse order of removal.
| •
|
To prevent wrinkles, make sure the material is stretched
evenly over the cover (B) before securing the hog-ring
clips (A).
|
| •
|
Replace the hog-ring clips with new ones using special
tool [C (09880-4F000)].
|
|
|
[5Door, Waggon]
[RH]
| • |
Put on gloves to protect your hands.
|
|
| • |
Use a plastic panel removal tool to remove interior trim pieces
to protect from marring the surface.
|
| • |
Take care not to bend or scratch the trim and panels.
|
|
| 1. |
Remove the rear seat cushion assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
|
| 2. |
Disconnect the rear seat cushion cover protector (A).
|
| 3. |
Remove the rear seat cushion frame (A).
|
| 4. |
After removing the hog-ring clips (A) on the rear of seat cushion and
remove the rear seat cushion cover (B).
|
| 5. |
Install in the reverse order of removal.
| •
|
To prevent wrinkles, make sure the material is stretched
evenly over the cover (B) before securing the hog-ring
clips (A).
|
| •
|
Replace the hog-ring clips with new ones using special
tool [C (09880-4F000)].
|
|
|
[3Door]
| • |
Put on gloves to protect your hands.
|
|
| • |
Use a plastic panel removal tool to remove interior trim pieces
to protect from marring the surface.
|
| • |
Take care not to bend or scratch the trim and panels.
|
|
| 1. |
Remove the j hook (A).
|
| 2. |
After removing the hog-ring clips (A) on the rear of seat cushion and
remove the rear seat cushion cover (B).
|
| 3. |
Install in the reverse order of removal.
| •
|
To prevent wrinkles, make sure the material is stretched
evenly over the cover (B) before securing the hog-ring
clips (A).
|
| •
|
Replace the hog-ring clips with new ones using special
tool [C (09880-4F000)].
|
|
|
Component Location
1. Rear seat cushion cover [LH]
2. Rear seat cushion cover [RH]
...
Component Location
[5Door, Waggon only]
1. Rear back armrest
...
Other information:
: Keyless Entry Settings
Switching Keyless Entry On and Off
Switch the ignition on using an original
key that has not been created as a
MyKey.
Press Settings on the touchscreen.
Press Vehicle Settings.
Press Locks.
Reprogramming the Unlocking Function
You can enable two-stage unlocking
function allowing you to un ...
: SYNC™ Troubleshooting
Your SYNC system is easy to use. However,
should questions arise, see the tables
below.
Use your regional Ford website at any time
to check your phone's compatibility,
register your account and set preferences
as well as access a customer
representative via an online chat (during
certain hour ...
Rear Seat Cushion Cover Components and components location
Rear Back Armrest Components and components location