Kia Cee'd: Quarter Fixed Glass / Repair procedures
| • |
Put on gloves to protect your hands.
|
|
| • |
Use seat covers to avoid damaging any surfaces.
|
|
| 1. |
Remove the rear pillar trim.
(Refer to Interior Trim - "Rear Pillar Trim")
|
| 2. |
Loosen the quarter fixed glass (A) mounting nuts.
|
Tightening torque :
3.9 ~ 4.4 N.m (0.4 ~ 0.45 kgf.m, 2.9 ~ 3.3 lb-ft)
|
|
| 3. |
Cut out the sealant using the sealant cutting tool [A(09861-31000)].
| •
|
Do not scrape down to the painted surface of the body;
damaged paint will interfere with proper bonding.
|
|
| •
|
Remove the rubber dam and fastereners from the body.
|
| •
|
Mask off surrounding surfaces before painting.
|
|
|
| 4. |
Remove the quarter fixed glass.
|
| 1. |
With a putt knife, scrape the old adhesive smooth to a thickness of
about 2mm (0.08 in.) on the bonding surface around the entire quarter
fixed glass flange.
| •
|
Do not scrape down to the painted surface of the body,
damaged paint will interfere with proper bonding.
|
| •
|
Mask off surrounding surfaces before painting.
|
| •
|
Remove the fasteners from the body.
|
|
|
| 2. |
Clean the body bonding surface with a sponge dampened in alcohol. After
cleaning, keep oil, grease and water from getting on the surface.
|
| 3. |
With a sponge, apply a light coat of glass primer along the edge of
the quarter fixed glass as shown, then lightly wipe it off with gauze
or cheese cloth :
| •
|
Do not apply body primer to the quarter fixed glass,
and do not get body and glass primer sponges mixed up.
|
| •
|
Never touch the primed surfaces with your hands. If
you do, the adhesive may not bond to the quarter fixed
glass properly, causing a leak after the quarter fixed
glass in installed.
|
| •
|
Keep water, dust, and abrasive materials away from the
primed surface.
|
|
|
| 4. |
With a sponge, apply a light coat of body primer to the original adhesive
remaining around the flange. Let the body primer dry for at least 10
minutes.
| •
|
Do not apply glass primer to the body, and be careful
not to mix up glass and body primer sponges.
|
| •
|
Never touch the primed surfaces with your hands.
|
|
|
| 5. |
Pack adhesive into the cartridge without air pockets to ensure continuous
delivery. Put the cartridge in a caulking gun, and run a bead of sealant
around the edge of the quarter fixed glass (A) as shown. Apply the adhesive
within 30 minutes after applying the glass primer. Make a slightly thicker
bead at each corner.
|
| 6. |
Install the quarter fixed glass.
|
| 7. |
Let the adhesive dry for at least one hour, then spray water over the
quarter fixed glass and check for leaks. Mark the leaking areas, let
the quarter fixed glass dry, then seal with sealant. Let the vehicle
stand for at least four hours after quarter fixed glass installation.
If the vehicle has to be used within the first four hours, it must be
driven slowly.
|
| 8. |
Reinstall all remaining removed parts.
|
| 9. |
Install the rear pillar trim.
|
Component Location
1. Quarter fixed glass
...
Other information:
Kia Cee'd JD Owners Manual: Manual type
To adjust the headlight beam level
according to the number of the passengers
and the loading weight in the luggage
area, turn the beam leveling switch.
The higher the number of the switch is
positioned, the lower the headlight beam
level. Always keep the headlight beam at
the proper l ...
Kia Cee'd JD Owners Manual: Vanity mirror lamp
Push the switch to turn the light on or off.
: The lamp will turn on if
this button
is pressed.
: The lamp will turn off
if this button
is pressed.
CAUTION
- Vanity mirror lamp
Always have the switch in the off
position when the vanity mirror
lamp is not in use. If the ...
Components and components location
Floor Carpet