Kia Cee'd: Cylinder Head Assembly / Cylinder Head Cover Repair procedures

Kia Cee'd JD Service Manual / Engine Mechanical System / Cylinder Head Assembly / Cylinder Head Cover Repair procedures

Removal

1.	Remove the engine cover.

2.	Disconnect the battery negative terminal.

3.	Disconnect the intake OCV(Oil Control Valve)connector, exhaust OCV(Oil Control Valve)connector, and then remove exhaust OCV valve. (Refer to Fuel System - "CVVT Oil Control Valve (OCV)")

4.	Remove the ignition coil. (Refer to Engine Eletrical System -"Ignition Coil")

5.	Disconnect the injector extension connector, the VIS (Variable intake system) connector and the PCSV (Purge control solenoid valve) connector. (Refer to Fuel System - "Engine Control System")

6.	Remove the FPCV (Fuel pressure control valve) connector, the intake CMPS (Camshaft position sensor) connector and the exhaust CMPS (Camshaft position sensor) connector, oxygen sensor connectors. (Refer to Fuel System - "CVVT Oil Control Valve (OCV)")

7.	Remove the PCV(Positiv Crankcase Ventilation) hose (A).

8.	Remove the high pressure fuel pump. (Refer to Fuel System - "High Pressure Fuel Pump")

9.	Remove the cylinder head cover(A), gasket(B).

Installation

Install the cylinder head cover (A) with a new gasket (B).

Do not reuse the disassembled gasket.

Tighten the cylinder head cover bolts (A) with the order and steps.

Tightening torque :

1st step: 3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)

2nd step: 7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

3.	Install the high pressure fuel pump. (Refer to Fuel System - "High Pressure Fuel Pump")

4.	Install the PCV(Positiv Crankcase Ventilation) hose (A).

5.	Install the FPCV (Fuel pressure control valve) connector, the intake CMPS (Camshaft position sensor) connector and the exhaust CMPS (Camshaft position sensor) connector, oxygen sensor connectors. (Refer to Fuel System - "CVVT Oil Control Valve (OCV)")

6.	Install the injector extension connector, the VIS (Variable intake system) connector and the PCSV (Purge control solenoid valve) connector. (Refer to Fuel System - "Engine Control System")

7.	Install the ignition coil. (Refer to Engine Eletrical System -"Ignition Coil")

8.	Install the intake OCV(Oil Control Valve)connector, exhaust OCV(Oil Control Valve)connector, and then remove exhaust OCV valve. (Refer to Fuel System - "CVVT Oil Control Valve (OCV)")

9.	Install the battery negative terminal.

10.	Install the engine cover.

Cylinder Head Cover Components and components location

Components 1. Cylinder head cover 2. Cylinder head cover gasket 3. Cam position sensor ...

CVVT & Camshaft Components and components location

Components 1. Exhaust CVVT 2. Intake CVVT ...

Other information:

Kia Cee'd JD Service Manual: Cluster Ionizer Description and operation
Description The cluster ionizer makes disinfection and decomposition of bad smell from the air-conditioner or inflow air. And it cleans the inside air of a vehicle. When running an air-conditioner or heater, it starts with "CLEAN" mode and repeats from "CLE ...

Kia Cee'd JD Owners Manual: Infant or small child
You should be aware of the specific requirements in your country. Child and/or infant seats must be properly placed and installed in the rear seat. For more information about the use of these restraints, refer to “Child restraint system” in this section. WARNING Every person in you ...