Removal [LHD] |
1. |
Turn ignition switch OFF and disconnect the negative (-) battery cable.
|
2. |
Remove the crash pad lower panel.
(Refer to Body - "Crash pad lower panel")
|
3. |
Remove the shower duct (A).
|
4. |
Disconnect the stop lamp switch connector (A).
|
5. |
Remove the brake pedal member mounting bolt (A).
|
6. |
Remove the snap pin (A) and clevis pin (B).
|
7. |
Remove the brake pedal member assembly mounting nuts and then remove
the brake pedal assembly.
|
Removal [RHD] |
1. |
Turn ignition switch OFF and disconnect the negative (-) battery cable.
|
2. |
Remove the crash pad lower panel.
(Refer to Body - "Crash pad lower panel")
|
3. |
Remove the junction box.
|
4. |
Disconnect the stop lamp switch connector (A).
|
5. |
Remove the brake pedal member mounting bolt (A).
|
6. |
Remove the snap pin (A) and clevis pin (B).
|
7. |
Remove the brake pedal member assembly mounting nuts and then remove
the brake pedal assembly.
|
Inspection |
1. |
Check the bushing for wear.
|
2. |
Check the brake pedal for bending or twisting.
|
3. |
Check the brake pedal return spring for damage.
|
4. |
Check the stop lamp switch.
|
Installation [LHD] |
1. |
Pre-tighten the bracket fixing bolt (A) in dash panel.
|
2. |
Install the brake booster and brake pedal member fixing nuts (A) securely.
|
3. |
Tighten the bolt (A) securely in dash panel.
|
4. |
Install the snap pin (A) and clevis pin (B).
|
5. |
Install the stop lamp switch securely.
|
6. |
Connect the stop lamp switch connector (A).
|
7. |
Adjust the brake pedal height and free play.
|
8. |
Check the brake pedal operation after installing the brake pedal.
|
9. |
Install the shower duct (A).
|
10. |
Install the crash pad lower panel.
(Refer to Body - "Crash pad lower panel")
|
11. |
Reconnect the battery negative cable.
|
Installation [RHD] |
1. |
Pre-tighten the bracket fixing bolt (A) in dash panel.
|
2. |
Install the brake booster and brake pedal member fixing nuts (A) securely.
|
3. |
Tighten the bolt (A) securely in dash panel.
|
4. |
Install the snap pin (A) and clevis pin (B).
|
5. |
Install the stop lamp switch securely.
|
6. |
Connect the stop lamp switch connector (A).
|
7. |
Adjust the brake pedal height and free play.
|
8. |
Check the brake pedal operation after installing the brake pedal.
|
9. |
Install the junction box.
(Refer to Body Electrical - "Relay Box")
|
10. |
Install the crash pad lower panel.
(Refer to Body - "Crash pad lower panel")
|
11. |
Reconnect the battery negative cable.
|
Adjustment |
Stop lamp switch clearance adjustment |
1. |
Disconnect the stop lamp switch connector (A).
|
2. |
Pull the locking plate (A) as indicated by the arrow.
|
3. |
Turn stop lamp switch 45° counterclockwise and remove it.
|
4. |
Fix the brake pedal arm and insert fully the stop lamp switch as hiding
contact part.
|
5. |
After inserting, turn the stop switch (A) 45° clockwise, and then assemble
locking plate (B) by pushing.
|
6. |
Confirm the gap between stop lamp switch and bracket.
|
7. |
Connect the stop lamp switch connector.
|
Kia Cee'd JD Service Manual: General information
General Troubleshooting
Information
Before Troubleshooting
1.
Check applicable fuses in the appropriate fuse/relay box.
2.
Check the battery for damage, state of charge, and clean and tight connections.
(Refer to Eng ...
Ford Escape 2020-2022 Owners Manual: Creating a MyKey - Vehicles With: Push Button Start. Creating a MyKey -
Vehicles With: Flip Key
Creating a MyKey - Vehicles With: Push Button Start
Remove the mat covering the backup
location.
Remove the key blade from the
transmitter.
Place the passive key in the position
shown, with the buttons facing upward.
Switch the ignition on.
Using your touchscreen, press Menu.
Press Set ...