Kia Cee'd: Front Seat Belt / Front Seat Belt Pretensioner Repair procedures
| • |
When installing the belt, make sure not to damage the pretensioner.
|
|
| 1. |
Remove the center pillar upper trim.
(Refer to Interior Trim - "Center Pillar Trim")
|
| 2. |
After loosening the mounting bolt, then remove the front seat belt upper
anchor (A).
|
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
| 3. |
After disconnecting the pretensioner connector lock pin, remove the
front seat belt pretensioner connector (B), loosen the mounting bolts,
then remove the front seat belt pretensioner (A).
|
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
| 4. |
Install in the reverse order of removal.
| •
|
Replace any damaged clips.
|
| •
|
Make sure the connector is plugged in properly.
|
|
|
[3Door]
| • |
When installing the belt, make sure not to damage the pretensioner.
|
|
| 1. |
Remove the rear inner outer trim.
(Refer to Interior Trim - "Center Pillar Trim")
|
| 2. |
After loosening the mounting bolt, then remove the front seat belt lower
anchor (A).
|
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
| 3. |
Remove the front seat belt upper anchor cover (A).
|
| 4. |
After loosening the mounting bolt, then remove the front seat belt upper
anchor (A).
|
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
|
|
| 5. |
After disconnecting the pretensioner connector lock pin, remove the
front seat belt pretensioner connector (B), loosen the mounting bolts,
then remove the front seat belt pretensioner (A).
|
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
| 6. |
Install in the reverse order of removal.
| •
|
Replace any damaged clips.
|
| •
|
Make sure the connector is plugged in properly.
|
|
|
Component Location
[5Door, Waggon]
1. Front seat belt pretensioner
[3Door]
1. Front seat belt ...
Component Location
[5Door, Waggon only]
1. Height adjust
...
Other information:
: Wipers
Wiper Precautions
Do not operate the wipers on a dry
windshield. This could scratch the glass or
damage the wiper blades. Use the
windshield washers before wiping a dry
windshield.
Fully defrost the windshield before you
switch the windshield wipers on.
Switch the windshield wipers off before
...
: Sounding the Panic Alarm. Locating Your Vehicle
Sounding the Panic Alarm
Press the button to sound the
panic alarm. Press the button
again, or switch the ignition on
to turn it off.
Note: The panic alarm only operates when
the ignition is off.
Locating Your Vehicle
Press the lock button twice
within three seconds. The turn
signal lamps fl ...
Front Seat Belt Pretensioner Components and components location
Height Adjust Components and components location